Passive hardware · SLS 3D printing

Phone mount

Name: Phone mount
Brand: benned
Availability: PreOrder

A single-piece desk or bar mount cut to your phone’s exact thickness, with a cable channel that keeps the charging lead out of the way.

Configure

Order today and it arrives around 24 September.

Device thickness11 mmMeasure with the case on — it is the number people get wrong most often.Device width78 mmAnything from 55 to 200 mm is qualified for production.Cradle angle62 degAnything from 45 to 78 deg is qualified for production.Wall thickness2.2 mmAnything from 1.4 to 4 mm is qualified for production.Base depth82 mmAnything from 55 to 130 mm is qualified for production.Material1.14 g/cm³, 55 MPaShip it assembled (+€5)2 steps, 2 minutes. As a kit it ships flatter and costs less to fly.Quantity1Tooling is amortised over our committed run of 5,000, so a single unit does not carry the whole mould.

€39per unit, incl. VAT · 8 working days

Reserve this build →

Generated specificationrev PHO-1AX2J47

8 working daysMade for your order · Air express, customs cleared

Or €19 in 38 days on the batch lane.

88 × 82 × 93 mmBounding box

63 gMass

PA12 + 30% glass fibreSLS 3D printing

€39incl. VAT, from €15.42

Parts — what is stocked and what is made for you
Body	Made to order	SLS 3D printing
Delivered	Assembled	2 min of assembly included

Parameters
Device thickness	11 mm	6–22 mm
Device width	78 mm	55–200 mm
Cradle angle	62 deg	45–78 deg
Wall thickness	2.2 mm	1.4–4 mm
Base depth	82 mm	55–130 mm

Computed
Tip-over angle	38.6 deg	target ≥ 15
Slot width	12.2 mm
Screen angle from vertical	28 deg	target ≥ 12, ≤ 45

Fits and tolerances — ISO 286, general dimensions ISO 2768-m (±0.3 mm)
Device slot	Ø11 H11/h11	clearance 0–0.2165 mm · needs a secondary operation

61Manufacturability
Buildable as specified

Device slot needs a secondary operation
H11/h11 at Ø11 mm asks for a tolerance the as-moulded process does not hold. The device must drop in one-handed; a loose fit plus a TPU liner beats a precise slot that a thicker case no longer enters.
→ Specify reaming or facing after the primary operation, and state it on the drawing.
Built in PA12 + 30% glass fibre, not PC/ABS
SLS 3D printing cannot run PC/ABS. On this lane the part is PA12 + 30% glass fibre: 1.35 g/cm³ against 1.14, and 110 MPa against 55. The surface is different too — printed parts have a fine matte grain that a moulded part does not.
→ Order on the batch lane to get PC/ABS as specified.
Speed is most of what you are paying for
Air freight is €8.11 of a €15.42 landed cost — 53% of it. This part is heavy enough that flying it costs more than making it.
→ The same configuration by sea takes about 38 working days and cuts the freight to roughly a fiftieth.
The moulded version carries draft the printed one does not
Body prints without draft on the express lane, but injection molding needs 1° on every face parallel to the pull. Over a 90 mm wall that moves the surface by about 1.6 mm.
→ If the two must be interchangeable, design with draft from the start and accept it on the printed part too.

Cost breakdown, per unit across a run of 1

Material	€0.63
Process	€4.88
Components	€0.97	3
Assembly	€0.11
Tooling, amortised	€0
Scrap allowance	€0.4
Freight + handling	€8.11
Import duty	€0.33
Landed cost	€15.42	before margin and VAT

What is fixed, and what is yours

The parameters above move; the components do not. Every unit uses the same released bill of materials, from the same certified suppliers, because changing the electronics means repeating the certification — expensive, slow, and invisible to you. The freedom is in the geometry, which is the part you actually see and touch.

body is made for your order by sls 3d printing. That split is the whole reason this can arrive in 8 working days instead of six weeks.

Bill of materials

Component	Supplier	Certification	Lead
TPU liner strip, adhesive backed	Standard	REACH	25 d
Self-adhesive felt pads	Standard	—	20 d
E-flute mailer, FSC	Local printer	FSC	20 d