Passive hardware · CNC turning + Cut to length from stock + SLS 3D printing

Headphone stand

Name: Headphone stand
Brand: benned
Availability: PreOrder

A cantilevered stand with a yoke radius matched to your headband, so the padding keeps its shape instead of creasing over a thin hook.

Configure

Order today and it arrives around 24 September.

Stand height285 mmAnything from 200 to 400 mm is qualified for production.Yoke radius34 mmLarger radius spreads the load across more of the headband pad.Base diameter128 mmThree stocked sizes; the base is a platform part.Arm offset58 mmAnything from 20 to 110 mm is qualified for production.Material2.7 g/cm³, 276 MPaFinishCoatings add thickness, and that thickness is inside the tolerance chain — which is why the fit table below moves when you change this.Ship it assembled (+€10)4 steps, 5 minutes. As a kit it ships flatter and costs less to fly.Quantity1Tooling is amortised over our committed run of 1,000, so a single unit does not carry the whole mould.

€99per unit, incl. VAT · 8 working days

Reserve this build →

Generated specificationrev HEA-0E4JD2U

8 working daysMade for your order · Air express, customs cleared

Or €54 in 38 days on the batch lane.

186 × 128 × 285 mmBounding box

676 gMass

Aluminium 6061-T6Cut to length from stock

€99incl. VAT, from €43.52

Parts — what is stocked and what is made for you
Turned base	Stocked	CNC turning
Post	Made to order	Cut to length from stock
Yoke	Made to order	SLS 3D printing
Delivered	Assembled	5 min of assembly included

Parameters
Stand height	285 mm	200–400 mm
Yoke radius	34 mm	18–60 mm
Base diameter	128 mm	90–190 mm
Arm offset	58 mm	20–110 mm

Computed
Tip-over angle with 400 g headphones	10.9 deg	target ≥ 10
Headband contact arc	82 mm	target ≥ 60

Fits and tolerances — ISO 286, general dimensions ISO 2768-m (±0.5 mm)
Post into base	Ø18 H7/g6	clearance 0.0067–0.0348 mm · needs a secondary operation

73Manufacturability
Buildable as specified

Post into base needs a secondary operation
H7/g6 at Ø18 mm asks for a tolerance the as-moulded process does not hold. Cantilevered load: any slop here becomes visible lean at the yoke.
→ Specify reaming or facing after the primary operation, and state it on the drawing.
Speed is most of what you are paying for
Air freight is €23.55 of a €43.52 landed cost — 54% of it. This part is heavy enough that flying it costs more than making it.
→ The same configuration by sea takes about 38 working days and cuts the freight to roughly a fiftieth.
The moulded version carries draft the printed one does not
Yoke prints without draft on the express lane, but injection molding needs 1° on every face parallel to the pull. Over a 90 mm wall that moves the surface by about 1.6 mm.
→ If the two must be interchangeable, design with draft from the start and accept it on the printed part too.

Cost breakdown, per unit across a run of 1

Material	€5.23
Process	€10.62
Components	€1.84	3
Assembly	€0.27
Tooling, amortised	€0.03
Scrap allowance	€1.08
Freight + handling	€23.55
Import duty	€0.9
Landed cost	€43.52	before margin and VAT

What is fixed, and what is yours

The parameters above move; the components do not. Every unit uses the same released bill of materials, from the same certified suppliers, because changing the electronics means repeating the certification — expensive, slow, and invisible to you. The freedom is in the geometry, which is the part you actually see and touch.

The parts that do not change — turned base — are made in volume and held in stock, so their tooling is spread over every configuration we sell and their lead time is zero. post and yoke are made for your order by cut to length from stock. That split is the whole reason this can arrive in 8 working days instead of six weeks.

Bill of materials

Component	Supplier	Certification	Lead
TPU liner strip, adhesive backed	Standard	REACH	25 d
Self-adhesive felt pads	Standard	—	20 d
Rigid gift box, FSC board	Local printer	FSC	25 d